Solid-state solvolysis of thiophene-substituted trityl-type alcohols: nucleophilic substitution induced by gas-solid contact.

The nucleophilic substitution reaction by gas-solid contact has been investigated. When 9-thienothienylfluoren-9-ol derivatives were coground with dichlorodicyanoquinone (DDQ) and then exposed to methanol vapor, the corresponding 9-methoxyfluorenes were obtained in 15-70% yields. Throughout the whole procedure the solid state was retained. The generation of a radical cation in the coground solids via charge-transfer interaction between the substrate alcohol and DDQ was suggested by the ESR spectrum. The mechanism involving the collapse of the radical cation to generate a proton, which acts as a catalyst to afford the carbocation, was deduced based on the electrochemical oxidation of the substrate in solution. The propagation of the substitution reaction in the solid state has been shown for the carbocation upon contact with methanol vapor. The crystalline inclusion compounds of 9-thienothienylfluoren-9-ol derivatives incorporating methanol as a guest were exposed to HCl gas. This gas-solid reaction also led to the formation of the corresponding methoxy compounds maintaining the solid state. Through this work a new consequence of solid-state cogrinding is deduced.     

Application of 28Mg to the kinetic study of Mg uptake by rice plants

The time course of Mg uptake and release using intact rice plants and ²⁸Mg as a tracer is presented. Since there is no conventional Mg tracer available, ²⁸Mg was produced via ²⁷Al(α, 3p)²⁸Mg reaction using a cyclotron. Using the purified ²⁸Mg tracer, it was found that the uptake amount of ²⁸Mg by the rice plants increased linearly during 30 min of application. After ²⁸Mg treatment for 90 min, the roots were sequentially washed with iced solution for 120 min. Within about 10 min, almost all of the ²⁸Mg, that was thought to be weakly bound to the apoplast, was washed away.     

H Nmr Spectra of Oligosaccharide Substituted Cyclodextrins

ABSTRACT

¹H NMR spectra of some oligosaccharide substituted cyclodextrins composed of only α-D-glucose units are analysed. Chemical shifts of protons of each glucosyl group of the chain were determined by experiments with the HOHAHA pulse technique. In spite of the similar kinds of protons, dispersion of chemical shifts is observed. The most dispersed proton is the anomeric proton, and the largest change in the chemical shifts is 0.5 ppm.     

Addition of alkyl radicals, generated from carboxylic acids via photochemical decarboxylation, to glyoxylic oxime ether: a mild and efficient route to α-substituted α-aminoesters

Radical addition to a glyoxylic oxime ether was accomplished under mild conditions using an alkyl radical generated from a free carboxylic acid via photochemical decarboxylation. The photoreaction provided an efficient route to α-substituted α-aminoesters from carboxylic acids and oxime ether.     

High-Quality Protein Crystal Growth of Mouse Lipocalin-Type Prostaglandin D Synthase in Microgravity

Lipocalin-type prostaglandin (PG) D synthase (L-PGDS) catalyzes the isomerization of PGH(2) to PGD(2) and is involved in the regulation of pain and of nonrapid eye movement sleep and the differentiation of male genital organs and adipocytes, etc. L-PGDS is secreted into various body fluids and binds various lipophilic compounds with high affinities, acting also as an extracellular transporter. Mouse L-PGDS with a C65A mutation was previously crystallized with citrate or malonate as a precipitant, and the X-ray crystallographic structure was determined at 2.0 ? resolution. To obtain high-quality crystals, we tried, unsuccessfully, to crystallize the C65A mutant in microgravity under the same conditions used in the previous study. After further purifying the protein and changing the precipitant to polyethylene glycol (PEG) 8000, high-quality crystals were grown in microgravity. The precipitant solution was 40% (w/v) PEG 8000, 100 mM sodium chloride, and 100 mM HEPES-NaOH (pH 7.0). Crystals grew on board the International Space Station for 11 weeks in 2007, yielding single crystals of the wild-type L-PGDS and the C65A mutant, both of which diffracted at around 1.0 ? resolution. The crystal quality was markedly improved through the use of a high-viscosity precipitant solution in microgravity, in combination with the use of a highly purified protein.     

Synthesis and properties of high‐molecular‐weight stereo di‐block polylactides with nonequivalent D/L ratios

Di‐stereoblock polylactides (di‐sb‐PLA: PLLA‐b‐PDLA) having high molecular weight (M_n > 100 kDa) were successfully synthesized by two‐step ring‐opening polymerization (ROP) of L ‐ and D ‐lactides using tin(2‐ethylhexanoate) as a catalyst. By optimizing the polymerization conditions, the block sequences were well regulated at non‐equivalent feed ratios of PLLA and PDLA. This synthetic method consisted of three stages: (1) polymerization of either L ‐ or D ‐lactide to obtain a PLLA or PDLA prepolymer with a molecular weight less than 50 kDa, (2) purification of the obtained prepolymer to remove residual lactide, and (3) polymerization of the enantiomeric lactide in the presence of the purified prepolymer. Their ¹³C and ³¹P NMR spectra of the resultant di‐sb‐PLAs strongly supported their di‐stereo block structure. These di‐sb‐PLAs, having weight‐average molecular weights higher than 150 kDa, were fabricated into polymer films by solution casting and showed exclusive stereocomplexation. The thermomechanical analysis of the films revealed that their heat deformation temperature was limited probably because of their low crystallinity owing to the non‐equivalent PLLA/PDLA ratio. The blend systems of the di‐sb‐PLAs having complementary stereo‐sequences (the one with a long PLLA block and the other with long PDLA block) were also prepared and characterized to enhance the sc crystallinity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 794–801, 2010     

Mobility performance of a rigid wheel in low gravity environments

To investigate influences of gravity on mobility of wheeled rovers for future lunar/planetary exploration missions, model experiments of a soil-wheel system were performed on an aircraft during variable gravity maneuvers. The experimental set-up consists of a single rigid wheel and a soil bed with two kinds of dry sands: lunar soil simulant and Toyoura sand. The experimental results revealed that a lower gravity environment yields higher wheel slippage in variable gravity conditions. In addition to the partial gravity experiments, the same experiments with variable wheel load levels were also performed on ground (1 g conditions). The on-ground experiments produced opposite results to those obtained in the partial gravity experiments, where a lower wheel load yields lower slippage in a constant gravity environment. In low gravity environments, fluidity (flowability) of soil increases due to the confining stress reduction in the soil, while the effect of the wheel load on sinkage decreases. As a result, both of these effects are canceled out, and gravity seemingly has no effect on the wheel sinkage. In the meantime, in addition to the effect of wheel load reduction, the increase of the soil flowability lessens the shear resistance to the wheel rotation, as a result of which the wheel is unable to hold sufficient traction in low gravity environments. This suggests that the mobility of the wheel is governed concurrently by two mechanisms: the bearing characteristics to the wheel load, and the shearing characteristics to the wheel rotation. It appears that, in low gravity, the wheel mobility deteriorates due to the relative decrease in the driving force while the wheel sinkage remains constant. Thus, it can be concluded that the lunar and/or Mars’ gravity environments will be unfavorable in terms of the mobility performance of wheels as compared to the earth’s gravity condition.     

Influence of processing variables on the formation of La2Zr2O7 in transferred arc plasma torch processing

The transferred arc plasma (TAP) torch process has various noteworthy features such as extremely high temperatures, low environmental impact and short processing time which makes it the most suitable technique for synthesizing ceramic composite materials. Furthermore, it is a direct two-step technique which by its virtue of high temperature and power density paves way for high production rate. Hence in this study, an effort has been made to utilize the TAP torch processing technique for the bulk production of La₂Zr₂O₇ with time effectiveness from the mixture of La₂O₃ and ZrO₂ powders (1:2 mol ratios) which were ball milled for 4 h. For this purpose, transferred arc plasma torch was specially designed in laboratory scale level and the operating parameters were optimized in order to achieve maximum La₂Zr₂O₇ formation efficiency. In this study, the phase and microstructure formation of the processed samples was analyzed via X-ray diffraction (XRD) and scanning electron microscope (SEM) images respectively. Moreover, EDX analysis was incorporated to highlight the superior influence of the longer processing time on the stoichiometric ratio of ZrO₂/La₂O₃ in the processed sample as against input power and the gas flow rate.     

Peptidehelicenes in solution and gel: chiral discrimination through interactions between two types of helixes

Helical [5]thiaheterohelicene 5HM, which rapidly interconverts between P and M enantiomers in solution, was connected to helical l-phenylalanine oligomers with an ester linkage to give peptidehelicenes (5Fn, where n: number of bonded phenylalanines). The characteristics of 5F4 and 5F5 with two types of helixes in a molecule were investigated, particularly in comparison with those of 5F1–5F3 with an incomplete coil of a peptide moiety. l-Phenylalanine peptide chains induced a shift in the equilibrium between the P and M helixes of 5HM toward the P side for all the 5Fns examined. The enantiomeric excess (ee) of the P form increased with a decrease in temperature, together with an elongation of the peptide chains. 5F4 and 5F5 in hot solutions of some solvents formed a gel at room temperature, whereas 5F1–5F3 showed no such behavior. In this gel, the stable helical form of the 5HM moiety in 5F4 and 5F5 was observed to be the M form in contrast to that in their solutions.